vmware虚拟机如何打开虚拟机(vmware创建的虚拟机在哪打开)

1. Find the working directory of the virtual machine, which is the folder where the virtual machine is stored. You will see a folder ending with "lck". Delete them all, and you can start the virtual machine. If you are not worried about deleting them all at once, cut them elsewhere first; 1. Most of the time, the virtual machine cannot be opened because of firewall interception. The solution is interrupted. Internet, turn off the anti-virus software, and turn off the firewall 2. If the Internet is disconnected and there is still no response when opening the virtual machine after turning off the firewall, it may be that the software does not have enough permissions to run. At this time, you need to right-click to run the VMware solution as an administrator; it is a firewall problem. There are two solutions: 1. Turn off the firewall. 2. Add VMware in "Allow programs to communicate through Windows Firewall". You can try it. If it is as you said, click to open the virtual machine and there is no response at all. An error warning will pop up. Then these two I wish you a solution. The specific solutions are as follows: 1. First open the control panel and find the management tools. 2. Open the management tools and find the service inside. 3. Double-click the service to enter and find the VMware Authorization Service. 4. Click Start on the left. 5. Click again after starting. The virtual machine can be turned on.
2. If possible, you don’t need to do the following steps. 4 Right-click the computer and click Management. 5 Click Services and Application Services. 6 Find the vmware service "VMware Authorization Service, and set it to automatically start and open. 7 Pass The above steps can successfully open and use the VMware virtual machine; 1. Click the "Start" button in the lower left corner and click "Computer Management" 2. Select "Service and Application Management", click the "Service" drop-down menu and select the "VMware Authorization Service" file 3. Double-click to open it. Change the startup type to "automatic" to open the virtual machine normally; 1. Use anti-virus software to kill viruses, recommend NOD32, Kabasi, and Rising. 2. Delete VMware in safe mode, and then reinstall it. 3. Check whether VMware is disabled in the WINDOWS service. Service, if there is one, start it. 4 If the recently installed software conflicts with VMware, uninstall the conflicting software and find similar software to replace the conflicting software V.
3. Select the one that is not the local optical drive and add the ISO file to In this optical drive, click Confirm, then select the VM power BIOS item from the virtual machine menu to boot. Otherwise, it will be difficult to enter the BIOS on the screen. After booting, enter BOOT to boot the optical drive. After the installation is completed, resume booting from the hard disk. ; First check the location of the virtual machine file, open the file location, check the vmware text document, open it and search for the pid text. You can also pull it to the right and you will see it. Generally, the result obtained on the first line is that the virtual machine entered The pid value of the farm is displayed in the Task Manager Performance Resource Monitor 5 resource; when installing the VM for the first time, if this prompt appears, you can try the following method. Enter the system preferences, select Security and Privacy under the General tab, and "Allow access from the following locations" If you don’t have any source options, open the terminal and enter the following command again; if your computer is a 64-bit computer system, if not, then you need to download a 32-bit virtual machine. It is a 64-bit operating system, so you may need to re-download a compatible version of the virtual machine software and reinstall it; if you cannot find this service at all, please download the official full version and reinstall it. Summary The virtual machine power cannot be turned on. Question: Open the host control panel management tool service, find the VMware authorization service VMwareAuthorizationservice, and set this service to the automatic startup type; vmwareworkstation10 cannot open the virtual machine. Solution 1: Use anti-virus software to kill the virus. It is recommended that NOD32 Cabasi Rising 2 delete VMware in safe mode. , and then reinstall. 3 Check whether VMware related services are disabled in the WINDOWS service. If so, start 4 the recently installed software and VMwar; Arm cannot be opened, and the virtual machine stops automatically after running half way. It may be that the system has insufficient memory. As a result, reasonable resources cannot be provided and the storage resources he needs cannot be provided.
4. 2 Right-click Start, click Computer Management, PS can also right-click this computer, click Manage 3 Double-click Services and Applications 4 Double-click Services 5 Find and double-click VMware Authorization Service 6 Change the startup type to Automatic, Apply OK 7 Accept After that, you can open the virtual machine normally; I have also encountered this problem. After many attempts and research, I found that the problem lies in the VMs. Just close the VMs to open the virtual machine. To close the VMs, edit=Preferences=ShareVMs and click DisableSharing. After clicking, it will become EnableSharing, and you can open the virtual machine normally; "devvmmon cannot be opened" The solution conflicts with HAXM or docker. Let's talk about the solution to the haxm conflict on mac. 1. Before starting vmwarefushion, uninstall the haxm kernel module sudokextunloadLibraryExtensionsintelhaxmkext, and then you can Start vmwarefushion2 normally.

More and more people are using Mac computers now, and some new users don’t know how to enable/exit full-screen mode for VMware virtual machines. Next The editor will introduce to you the specific steps.
How to enter full screen for a virtual machine
1. The first step is to open the virtual machine, and then click on the green icon according to the arrow in the picture below.
2. The second step is to successfully enable full-screen mode as shown in the picture below.
How to exit full-screen virtual machine
1. First, move the mouse to the top according to the arrow in the picture below, and then leave it there for a few seconds.
2. In the second step, in the pop-up menu bar, click the green icon again according to the arrow in the picture below.
3. Finally, as shown in the picture below, the full-screen mode is successfully exited.

To use the virtual machine that comes with Windows, first make sure that Windows is the professional version or other version that supports virtual machines. Windows Home Edition does not support Windows For the virtual machine that comes with it, please make sure that the computer hardware can meet the running conditions of the Windows virtual machine. This applies to all Windows versions.

Generally, the Windows virtual machine (Hyper-U) function is not turned on by default in Windows and needs to be installed manually. The specific steps to install a Windows virtual machine (Hyper-U) are as follows:

1. Open the "Control Panel".

The "Control Panel" cannot be found on the "Desktop" and can be added manually in the "Desktop Icon Settings".

Figure 1 Desktop icon settings

2. Find "Programs" in the "Control Panel" and open it. Find "Turn Windows features on or off" in "Programs and Features" and click to turn it on.

Figure 2 Program

Figure 3 Program and Function
/>

3. Check "Hyper-U" in the window that opens, click OK, and wait for the installation to complete.

Figure 4 Windows functions

The above steps are applicable to Windows 7, 8, 10, and 11!

Finally, open Hyper-U, install the operating system and it is ready to use.

If Hyper-U is not available in Windows, you can also choose a third-party virtual machine. Commonly used ones include VMwareworkstation (free version) and OracleVMVitualBox (open source and free).