vmware虚拟机未知选项怎么解决(虚拟机vmware不能打开怎么办)

When using a VMware virtual machine, sometimes you will encounter the problem that the simple installation cannot manually start the VMwareTools installation. The following are some possible solutions:
1. Check the operating system version: First make sure your operating system is compatible with VMwareTools. Make sure the version of VMware you are using supports your operating system. If the VMware version is too old, you may need to upgrade to the latest version.
2. Confirm the VMwareTools installation file: Check whether the VMwareTools installation file is available. Sometimes the downloaded installation file may be corrupted or incomplete. Try re-downloading the installation file to make sure it is intact.
3. Check the virtual machine settings: In VMware, ensure that VMwareTools installation has been enabled in the virtual machine settings. Open the virtual machine settings, click "Options" or "Settings" and select the "VMwareTools" tab. Make sure the "Install/Upgrade" option is enabled.
4. Manually install VMwareTools: If the simple installation cannot start the VMwareTools installation, you can try manual installation. Open the CD/DVD drive of the virtual machine and mount the VMwareTools installation file to the virtual machine. Then open a file browser in the virtual machine, find and run the installer.
5. Check the virtual machine network connection: Sometimes the virtual machine network connection problem may cause the VMwareTools installation to fail to start. Make sure the virtual machine network connection is normal. You can check and configure the network connection through the "Network Adapter" option in the virtual machine settings.
These are some common solutions that you can try to solve the problem that the simple installation cannot start the VMwareTools installation manually. If the problem persists, it is recommended to consult VMware official documentation or seek help from VMware technical support.

VMware virtual machines can run multiple systems on one machine at the same time. Many users will install and run the win7 system through virtual machines. , but encountered some problems when using it. Some users of the win7 system reported that when running the VMware virtual machine, an internal error prompted that the virtual machine could not be used, resulting in the inability to use the virtual machine. What should I do? Let’s take a look at it with the editor. Let’s look at the specific solutions.
Solution:
1. Just "run as administrator" VMwareWorkstation is enough;
2. VMwareWorkstation prompts an internal error when running and it is not a virtual machine. The problem is caused by system permissions. This type of error can be solved by running the VMware Workstation virtual machine as an administrator.
I will tell you what to do when the Win7 system prompts that an internal error cannot be used when running a VMware virtual machine. Users who encounter such a situation may wish to refer to the above methods to solve it.

1. Find the working directory of the virtual machine, which is the folder where the virtual machine is stored. You will see a folder ending with "lck". Delete them all, and you can start the virtual machine. If you are not worried about deleting them all at once, cut them elsewhere first; 1. Most of the time, the virtual machine cannot be opened because of firewall interception. The solution is interrupted. Internet, turn off the anti-virus software, and turn off the firewall 2. If the Internet is disconnected and there is still no response when opening the virtual machine after turning off the firewall, it may be that the software does not have enough permissions to run. At this time, you need to right-click to run the VMware solution as an administrator; it is a firewall problem. There are two solutions: 1. Turn off the firewall. 2. Add VMware in "Allow programs to communicate through Windows Firewall". You can try it. If it is as you said, click to open the virtual machine and there is no response at all. An error warning will pop up. Then these two I wish you a solution. The specific solutions are as follows: 1. First open the control panel and find the management tools. 2. Open the management tools and find the service inside. 3. Double-click the service to enter and find the VMware Authorization Service. 4. Click Start on the left. 5. Click again after starting. The virtual machine can be turned on.
2. If possible, you don’t need to do the following steps. 4 Right-click the computer and click Management. 5 Click Services and Application Services. 6 Find the vmware service "VMware Authorization Service, and set it to automatically start and open. 7 Pass The above steps can successfully open and use the VMware virtual machine; 1. Click the "Start" button in the lower left corner and click "Computer Management" 2. Select "Service and Application Management", click the "Service" drop-down menu and select the "VMware Authorization Service" file 3. Double-click to open it. Change the startup type to "automatic" to open the virtual machine normally; 1. Use anti-virus software to kill viruses, recommend NOD32, Kabasi, and Rising. 2. Delete VMware in safe mode, and then reinstall it. 3. Check whether VMware is disabled in the WINDOWS service. Service, if there is one, start it. 4 If the recently installed software conflicts with VMware, uninstall the conflicting software and find similar software to replace the conflicting software V.
3. Select the one that is not the local optical drive and add the ISO file to In this optical drive, click Confirm, then select the VM power BIOS item from the virtual machine menu to boot. Otherwise, it will be difficult to enter the BIOS on the screen. After booting, enter BOOT to boot the optical drive. After the installation is completed, resume booting from the hard disk. ; First check the location of the virtual machine file, open the file location, check the vmware text document, open it and search for the pid text. You can also pull it to the right and you will see it. Generally, the result obtained on the first line is that the virtual machine entered The pid value of the field is displayed in the Task Manager Performance Resource Monitor 5 resource; when installing the VM for the first time, if this prompt appears, you can try the following method. Enter the system preferences, select Security and Privacy under the General tab, and "Allow access from the following locations" If you don’t have any source options, open the terminal and enter the following command again; if your computer is a 64-bit computer system, if not, then you need to download a 32-bit virtual machine. It is a 64-bit operating system, so you may need to re-download a compatible version of the virtual machine software and reinstall it; if you cannot find this service at all, please download the official full version and reinstall it. Summary The virtual machine power cannot be turned on. Question: Open the host control panel management tool service, find the VMware authorization service VMwareAuthorizationservice, and set this service to the automatic startup type; vmwareworkstation10 cannot open the virtual machine. Solution 1: Use anti-virus software to kill the virus. It is recommended that NOD32 Cabasi Rising 2 delete VMware in safe mode. , and then reinstall. 3 Check whether VMware related services are disabled in the WINDOWS service. If so, start 4 the recently installed software and VMwar; Arm cannot be opened, and the virtual machine stops automatically after running half way. It may be that the system has insufficient memory. As a result, reasonable resources cannot be provided and the storage resources he needs cannot be provided.
4. 2 Right-click Start, click Computer Management, PS can also right-click this computer, click Manage 3 Double-click Services and Applications 4 Double-click Services 5 Find and double-click VMware Authorization Service 6 Change the startup type to Automatic, Apply OK 7 Accept After that, you can open the virtual machine normally; I have also encountered this problem. After many attempts and research, I found that the problem lies in the VMs. Just close the VMs to open the virtual machine. To close the VMs, edit=Preferences=ShareVMs and click DisableSharing. After clicking, it will become EnableSharing, and you can open the virtual machine normally; "devvmmon cannot be opened" The solution conflicts with HAXM or docker. Let's talk about the solution to the haxm conflict on mac. 1. Before starting vmwarefushion, uninstall the haxm kernel module sudokextunloadLibraryExtensionsintelhaxmkext, and then you can Start vmwarefushion2 normally.